No-Bull Directions For Using One Step No Rinse Cleanser

One Step No Rinse CleanserThe directions on the container of One Step No Rinse Cleanser simply say to rinse your equipment with the solution. Is there a minimum amount of contact time one must allow for the solution to work prior to using the sanitized equipment? The results of an online search stated anywhere from 30 seconds to 2 minutes. I know the safe route would be to let it sit for at least 2 minutes, but I’d rather not stand there waiting if I don’t have to.

Name: Paul
State: Missouri
Hello Paul,

The One Step No Rinse Cleanser is actually an oxygenating cleanser. This means that it uses a burst of oxygen from the solution to do the sanitizing. This high oxygen level actually destroys any unwanted microbes.

The great thing about any oxygenating cleanser is that it gives the biggest burst of oxygen while the solution is evaporating off the surface of what is being sanitized. In other words, the contact time with the solution is not what really matters. What matters is that the solution be allowed to evaporate without interruption after being taken out of the solution. The amount of time in the One Step solution is not critical. This is way the directions seem so vague.

The only situation when the length of time would matter is if you are treating a piece of equipment that has a lot of tight spots, or has a surface that is complex and Shop Basic A Cleansernot smooth. A couple examples of this would be a nylon brush or a straining screen. In both cases you would want to give “some” time for the solution to work its way in between and onto the surface of each nylon bristle or into the corner of each square of the screen. This could require a few seconds due to the surface tension of the solution.

The flip-side of this is when sanitizing a surface that is smooth, like glass, no time is required in the solution at all. Just dip or apply with a rag and allow to evaporate. Again, the evaporation from the surface is what’s key, not the time in the solution.

If you want to get the most out of the One Step No Rinse Cleanser you would allow your equipment to dry completely before using. However, I understand that following such directions would not be practical in a lot of situations, since it would make things way too time consuming. So as a matter of practicality, I would follow these directions: dip or or wipe with a rag the equipment with the solution of One Step No Rinse Cleanser, then allow to dry for 5 minutes.

One final not I’d like to make is that the One Step No Rinse Cleanser is not a Shop Sanitizerssoap or detergent in any way. It is not designed for or intended to release grime from your wine making equipment. This is something that needs to be done with a dish soap or similar, beforehand. The One Step No Rinse Cleanser is strictly for sanitizing your wine making equipment. It is designed to kill any molds, bacteria, etc.

Happy Winemaking,
Ed Kraus
Ed Kraus is a 3rd generation home brewer/winemaker and has been an owner of E. C. Kraus since 1999. He has been helping individuals make better wine and beer for over 25 years.

12 thoughts on “No-Bull Directions For Using One Step No Rinse Cleanser

  1. So this product is not really a cleanser but a sanitizer …correct?? Having said that…does it do the same as the metabisulfite solutions?

  2. Bob, the terms "cleanser" and "sanitizer" have been obliterated by the FDA. They have strict rules as to what terminology can be applied to one set of ingredients verses another. From a homebrewer’s standpoint, either will easily rid your equipment of any harmful microbes and there is absolutely no reason to use more than one product just to cover both words. Use either a sanitizer or a cleanser and your beer will be safe. As for comparing them with a sulfite solution, all the cleanser and sanitizers I’ve seen on the market for home brewing are much stronger than a normal strength sulfite solution when used as directed.

  3. Can this cleanser solution be used to rinse out bottles just prior to bottling? I have been using metabisulfate solution but I recently got judges feedback on my wine in which they said the wine had a sulfur smell. Thanks

    • Mary, the One Step No rinse Cleanser solution will not stay effective for later use. It should be used within minutes or a few hours.

  4. I rinse my carboys with one step before use. Do I need to need to allow them to completely dry before I use them?

    • Larry, as it says in the article, if you want the best from the One Step then you want to allow it to dry first. However, sometimes that is not practical. If you do not have time to wait for it to dry, dip or or wipe with a rag the equipment with the solution of One Step No Rinse Cleanser, then allow to dry for 5 minutes. However, with a carboy, this may be difficult to do.

Leave a Reply

Your email address will not be published. Required fields are marked *